- Swing out
- Need a competent welder
- XJ high steer install and track bar fix
- Bumper Time
- Locating a control box for a winch
- Steel shops in the South Hills?
- Frame welding
- 4 door JK cage additions
- Gonna give JK chick a run for her money
- Need mirror extensions for towing.
- Fiberglass tub swap
- Local Fabs shops to West/Alleg counties
- Operation narrowed D44HP into a TJ
- Tube Fenders
- anyone have a reamer for moog es2074 tie rods?
- HFO fabrication shout out!
- Tube Scouting
- Check Engine light on after Cat was cleared out
- Placing a tube order
- XJ rear tire carrier - Frame reinforcment
- Bender / Notcher
- Plasma table
- Rock slider fab for XJ
- Critique my boogers!!!
- Welding/Brazing Magnesium
- Who wants a side job?
- Rear seat for the kiddos
- Need a local machine shop
- 55 gal drum heater
- Tube Bender in Beaver Co
- Xtreme Offroad Center in Butler?
- New seats for the XJ
- My first try at fab work.
- TJ is getting some love
- I don't know enough about cars
- Need some rockers replaced
- Good Welder For Heavy Duty Control Arm Mount Brackets?
- The sound of a grinder, smell of burning metal
- Installing Rubicon axles in my 2000 TJ.
- The ooooooooh so bad 32.
- ditched my unit bearings and 30 spline stubs on the TJ
- D30 HP Pinion
- Prepping for paint on odd shaped plastics
- Does anybody have any experience with this high steer kit?
- Straight outta Nascar...
- Suggest a Plasma Cutter
- Ordered my 4x8 CNC Plasma
- Hard top roof rack
- GenRight Rocker Install
- Control Arms?
- Daystar stingers
- A whole bunch of sexy just showed up today.
- FINALLY a new suspension
- Made some A-Pillar Light Mounts
- Cheap and quick co2 tank mount?
- Talk me into out of this
- Poly bushing
- front drive shaft
- JK Hardtop insulation, rack, bed line &/or painting of interior, bed line top.... ADVISE
- Fab help wanted
- Where to buy DOM tube?
- Looking for a fab shop in the South Hills
- Welding Axle Sleeves and C gussets... and some small skids... where to go?!
- Bumper I built for a customer
- Over Heating???
- Changing up the Front end
- The Filthy3
- Flashback arrestor
- TJ engine bay question
- Best way to weld on brackets on my front axle
- Junkyard beater Turbo YJ
- Lunchbox locker's and carrier?
- Shafts/balljoints dilema
- Miller Econo Twin HF
- Cherokee Rockers
- 6.0 Vortec LQ9 swap into a YJ
- Axle tube repair
- Frame Welder needed
- Screamn56 YJ backhalf
- But WHERE would you wheel it?!?!
- Add a leaf problems!!!HELP
- Rip off??
- Hack N Tap
- My new gauge faces
- Raised my stock XJ flares
- Budget XJ long arm plan
- Looking for a cage file in bend tech
- SOA Problems
- Header instalation?
- I am looking for fab shops and off road shops
- Plasma tables post up
- 231j rebuild
- Hot Max wire?
- steel cowl hood upgrade
- Tire confusion for my 12 JK
- Need a shop to do floor pans and rockers
- where can i buy
- Weld on clevis mount?? Who sells them reasonable??
- Control Arm Brackets
- Gear Guru's - Pattern Check
- Cage questions
- 318 Magnum kegger mod
- Welding Help Needed
- Did toob rockers/sliders on my XJ this week
- Garage wiring
- So who does exhaust welding???
- need a 2" hole
- South of Pittsburgh Machine Shops?
- Dana 30 - Spindle Bearing question
- WHO'S up for a challenge - need some custom rock sliders...
- Shift knob adapters
- Powder coating
- NP241-D: Slipyoke eliminator, or...???
- Sand blasting
- Ordering a bender...
- Trimmed jk fenders?
- Any Die Casting Shops somewhat local to Pittsburgh?
- In search of suspension modification/fabrication.
- Welder Shopping - ESAB Miniarc 161LTS
- Iron-Armor rear corner armor
- Electronics shop?
- WJ rear bumper with tire carrier, DIY flat pack
- Under seat lock box in 2 door JK
- Iron Rock Double Shear Track Bar Upgrade #10138 2000 Xj
- superduty axles under my xj?
- shock info
- Shop to setup gears
- Powder Coating stuff on Washington
- What should I do with all this steel??
- Installing after market lights to oem fog light switch
- Engine Builders (AMC 258)
- long arms on a budget
- Homemade metal brake
- I have a plan!
- Bought a power hacksaw
- Bought a power hacksaw
- powdercoater or painter
- Looking for help with axle upgrades
- Frame repair
- Oh whatever am I Building?...
- Cost of an Isuzu D44 Axle Swap
- Aluminum vs Steel Skid Plates
- Welder Around Pittsburgh
- Needing someone to help CNC/manufacture item
- Plasma Cutter
- And now a crane
- Upgrade Upgrade! Welding cart upgrade
- Cut and turn