Slugger
04-11-2010, 08:04 PM
I decided that i wanted to take out my carpet and clean up the rust and herculine the inside of my XJ. It wasn't to badly rusted, but I wanted to clean it up before it got worse.
Here are some pictures of what I got done so far, just started touching up the XJ today.
to get the rust off i used wire wheels, and some green roloc discs. to scuff up the paint i am using medium surface discs just enough to get the paint off.
then I am using acetone to clean up before i put the herculiner on.
Day 1
http://i48.photobucket.com/albums/f223/elkerb/My%20jeep/DSCN0194.jpg
here it is with the silver stuff off now ( it was a pain getting the silver stuff off but after i got it off i did the best i could to get the rubber stuff that was stuck to it off by sanding it off )
http://i48.photobucket.com/albums/f223/elkerb/My%20jeep/DSCN0195.jpg
heres the drivers side floor panel
http://i48.photobucket.com/albums/f223/elkerb/My%20jeep/DSCN0191.jpg
passenger side
http://i48.photobucket.com/albums/f223/elkerb/My%20jeep/DSCN0198.jpg
heres the rear
http://i48.photobucket.com/albums/f223/elkerb/My%20jeep/DSCN0193.jpg
now here is the front cleaned up some
http://i48.photobucket.com/albums/f223/elkerb/My%20jeep/DSCN0203.jpg
http://i48.photobucket.com/albums/f223/elkerb/My%20jeep/DSCN0202.jpg
______________________________
Day 2-3
Here it is all scuffed up. Tomorrow im going to clean it with Acetone and then herculine it.
http://i48.photobucket.com/albums/f223/elkerb/My%20jeep/DSCN0216.jpg
http://i48.photobucket.com/albums/f223/elkerb/My%20jeep/DSCN0218.jpg
http://i48.photobucket.com/albums/f223/elkerb/My%20jeep/DSCN0217.jpg
I also took off the plastic step things and am going to herculine that in the front and rear
http://i48.photobucket.com/albums/f223/elkerb/My%20jeep/DSCN0213.jpg
then there was a few little rust holes so i put JB weld stick over it. the jb weld worked good. its as hard as a rock on there.
http://i48.photobucket.com/albums/f223/elkerb/My%20jeep/DSCN0215-1.jpg
Tomorrow i'll be herculining it and i'll update this thread once im done.
______________________________
here it is herculined. I plan to do the cargo area eventually. I still have a little less then half a gallon left out of the gallon of herculiner i bought.
I did two coats. I did the first coat, then waited 1 hour and 30 minutes and applied the second coat.
http://i48.photobucket.com/albums/f223/elkerb/My%20jeep/DSCN0254.jpg
http://i48.photobucket.com/albums/f223/elkerb/My%20jeep/DSCN0255.jpg
http://i48.photobucket.com/albums/f223/elkerb/My%20jeep/DSCN0253.jpg
http://i48.photobucket.com/albums/f223/elkerb/My%20jeep/DSCN0257.jpg
Here are some pictures of what I got done so far, just started touching up the XJ today.
to get the rust off i used wire wheels, and some green roloc discs. to scuff up the paint i am using medium surface discs just enough to get the paint off.
then I am using acetone to clean up before i put the herculiner on.
Day 1
http://i48.photobucket.com/albums/f223/elkerb/My%20jeep/DSCN0194.jpg
here it is with the silver stuff off now ( it was a pain getting the silver stuff off but after i got it off i did the best i could to get the rubber stuff that was stuck to it off by sanding it off )
http://i48.photobucket.com/albums/f223/elkerb/My%20jeep/DSCN0195.jpg
heres the drivers side floor panel
http://i48.photobucket.com/albums/f223/elkerb/My%20jeep/DSCN0191.jpg
passenger side
http://i48.photobucket.com/albums/f223/elkerb/My%20jeep/DSCN0198.jpg
heres the rear
http://i48.photobucket.com/albums/f223/elkerb/My%20jeep/DSCN0193.jpg
now here is the front cleaned up some
http://i48.photobucket.com/albums/f223/elkerb/My%20jeep/DSCN0203.jpg
http://i48.photobucket.com/albums/f223/elkerb/My%20jeep/DSCN0202.jpg
______________________________
Day 2-3
Here it is all scuffed up. Tomorrow im going to clean it with Acetone and then herculine it.
http://i48.photobucket.com/albums/f223/elkerb/My%20jeep/DSCN0216.jpg
http://i48.photobucket.com/albums/f223/elkerb/My%20jeep/DSCN0218.jpg
http://i48.photobucket.com/albums/f223/elkerb/My%20jeep/DSCN0217.jpg
I also took off the plastic step things and am going to herculine that in the front and rear
http://i48.photobucket.com/albums/f223/elkerb/My%20jeep/DSCN0213.jpg
then there was a few little rust holes so i put JB weld stick over it. the jb weld worked good. its as hard as a rock on there.
http://i48.photobucket.com/albums/f223/elkerb/My%20jeep/DSCN0215-1.jpg
Tomorrow i'll be herculining it and i'll update this thread once im done.
______________________________
here it is herculined. I plan to do the cargo area eventually. I still have a little less then half a gallon left out of the gallon of herculiner i bought.
I did two coats. I did the first coat, then waited 1 hour and 30 minutes and applied the second coat.
http://i48.photobucket.com/albums/f223/elkerb/My%20jeep/DSCN0254.jpg
http://i48.photobucket.com/albums/f223/elkerb/My%20jeep/DSCN0255.jpg
http://i48.photobucket.com/albums/f223/elkerb/My%20jeep/DSCN0253.jpg
http://i48.photobucket.com/albums/f223/elkerb/My%20jeep/DSCN0257.jpg