View Full Version : New dash
justin'sbig7
01-28-2011, 11:28 PM
with the wiring lately, i hit the point where i needed to get the dash done in the jeep. i had a piece of 18ga cut and braked at the local steel supplier... cost me 15 bucks. then i went down to S&S chassis supply in springdale and picked up the parts for the new steering shaft/column. after some work heres the new setup.
i am thinking about just clearcoating the bare steel instead of black paint, not sure yet though.
http://i48.photobucket.com/albums/f214/justinsbig7/fabrication/006-17.jpg
http://i48.photobucket.com/albums/f214/justinsbig7/fabrication/005-16.jpg
http://i48.photobucket.com/albums/f214/justinsbig7/fabrication/002-17.jpg
http://i48.photobucket.com/albums/f214/justinsbig7/fabrication/001-19.jpg
also mounted the VIAIR compressor
http://i48.photobucket.com/albums/f214/justinsbig7/fabrication/007-17.jpg
willysrule
01-29-2011, 12:53 AM
sweet!
justin'sbig7
02-05-2011, 08:49 PM
just waiting on the switches i ordered.
http://i48.photobucket.com/albums/f214/justinsbig7/fabrication/001-20.jpg
http://i48.photobucket.com/albums/f214/justinsbig7/fabrication/002-18.jpg
and i made a new transmission tunnel cover to give more room around the t-case
http://i48.photobucket.com/albums/f214/justinsbig7/fabrication/003-19.jpg
ridgerunner97
02-05-2011, 09:30 PM
Looks really nice Justin.
busij44
02-05-2011, 09:34 PM
Nice work Justin.
justin'sbig7
02-05-2011, 10:32 PM
Thanks! i am going to mount the gauges on the dash bar, but i am not sure if i am going to use the autometer pods or make my own panel type thing.
Deadman 94 xj
02-06-2011, 02:36 AM
The black looks killer!!!
justin'sbig7
02-17-2011, 09:02 PM
dash is done, i got all my switches from k-4 switches. found them on pirate and were awesome to deal with. switches are all triple o-ring sealed.
http://i48.photobucket.com/albums/f214/justinsbig7/fabrication/004-20.jpg
http://i48.photobucket.com/albums/f214/justinsbig7/fabrication/003-20.jpg
http://i48.photobucket.com/albums/f214/justinsbig7/fabrication/002-19.jpg
http://i48.photobucket.com/albums/f214/justinsbig7/fabrication/001-21.jpg
Mykal
02-17-2011, 09:13 PM
Very simple. I like it. Good work.
tjblair
02-17-2011, 10:13 PM
yah looks good man!
Deadman 94 xj
02-17-2011, 10:15 PM
Love it. It really turned out good!
justin'sbig7
02-17-2011, 11:07 PM
thanks yall!
justin'sbig7
02-27-2011, 06:14 PM
heres my view with the gauges all mounted (the vac will be changed to tach, the fuel will be water temp)
http://i48.photobucket.com/albums/f214/justinsbig7/fabrication/008-12.jpg
justin'sbig7
03-16-2011, 04:39 PM
Latest pic
http://i48.photobucket.com/albums/f214/justinsbig7/42184d50.jpg
http://i48.photobucket.com/albums/f214/justinsbig7/1412d70f.jpg
Deadman 94 xj
03-16-2011, 04:59 PM
Ready to roll!
ridgerunner97
03-16-2011, 05:37 PM
Literally!!! :082: I love your CJ Justin, it just keeps getting better and better. As time goes by its getting better like a good whiskey. :nod:
justin'sbig7
03-16-2011, 08:56 PM
Literally!!! :082: I love your CJ Justin, it just keeps getting better and better. As time goes by its getting better like a good whiskey. :nod:
thanks man! I appreciate the props, its been a lot of work over the years
Sycotik Skier
03-16-2011, 08:57 PM
Justin I wish my CJ was as awesome as yours
Powered by vBulletin® Version 4.2.2 Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.