It's of the front end of my ZJ buggy. Those of you on my facebook - no sharing.
This should be like "Where's Waldo" - but it's "what'd Matt break by putting the front end vertical and slamming it down on a junkyard car a few times.)
Well?
It's of the front end of my ZJ buggy. Those of you on my facebook - no sharing.
This should be like "Where's Waldo" - but it's "what'd Matt break by putting the front end vertical and slamming it down on a junkyard car a few times.)
Well?
Last edited by OverkillZJ; 04-11-2010 at 08:48 PM.
Damn, I was going to just copy and paste your facebook comment.
2000tj on D60's, custom long arms, 3link front, four link rear both locked with a 231/300 doubler twin sticked, Full Hydro steering, on 38 in boggers
looks like the track bar hit the ram and bent it, in turn denting the oil pan
03 s10 4x4
89 irocz mullet mobile
90 miata v8 project
The gibson has eyes! And? The worst (and funniest) of the damage is yet to be noticed. And proves why I HAAAATE unibodies.
nice bent coil over
03 s10 4x4
89 irocz mullet mobile
90 miata v8 project
I hope that's not bent...
looking closer it looks like you either broke the upper control arm or bent the ram's mount, but i cant tell.
03 s10 4x4
89 irocz mullet mobile
90 miata v8 project
Neither, the UCA is welded bent (in order to clear an HP30 axle which is no longer there.)
I won't tell, but its hard to spot, and props to Gibson
97 XJ Clayton Longarms 35s locked etc.
94 YJ MTO
98 5.9 ZJ Limited alllll original
02 Cummins 6spd HO Studs, Sticks, Box, Pump...
Track bar bracket is a little twisted (Twisted meaning FUBAR'd).
Best answer yet. It looks like when the rig landed, the mounting bolt for the steering ram made contact with the 1/4" DOM track bar, bending it, and pulling the passenger side unirail in (remember, this used to be a grand cherokee) which pulled the passenger side motor mount into the transmission cooling lines, into the enging block, and moved the whole driveline over about an inch.
In other words, don't build a buggy on a unibody vehicle! But I can't wait to rebuild it... After jumping it a few more times.
Jump it til it goes boom!
97 XJ Clayton Longarms 35s locked etc.
94 YJ MTO
98 5.9 ZJ Limited alllll original
02 Cummins 6spd HO Studs, Sticks, Box, Pump...
Wow! That's nuts. Although not all that surprising considering. Do you think some plating or reinforcements in that area might have helped?
That's what it seems like a lot of guys do. They go along the whole damn UB, strengthening up potentials. There's been a lot of talk latley on here about UB guys not having ability to hang with the "big" crowd. Now I think I see why!
You know I love some unibody vehicles considering it's what I learned on - but, building a hardcore rig on unibody is like building on top or swiss cheese - there will always be holes or something isn't right. the point that twisted was 3' between cage points and attached to 5/16" steel plate attached to the coilover mounting point.
My conclusion: Hey, it's a unibody. Let's jump it again.
LOL, point taken. I like the conclusion
I betcha a brace going from one rail to the other would have helped. Similar to ,but a lot stronger than, what RE sells for their trackbar brackets.
Either that or not jumping it lol.
2000tj on D60's, custom long arms, 3link front, four link rear both locked with a 231/300 doubler twin sticked, Full Hydro steering, on 38 in boggers
Where, under the motor, so that the ram would be desroyed, or desroy the oil pan as they made contact not only with themselves, but with your "brace" as well?
honesly, with what I did, I'm happy with the damage!
Ahh, I see. The bar and the brace would have bound together anyway.
Soooo, any plans to fix her yet? Just keep jumping it?
i think its time to buggy the 5.9
03 s10 4x4
89 irocz mullet mobile
90 miata v8 project
Honestly, the welds look good... the driveline is where it is, and, well, really I'll call it a "self clearing flaw" - I'm ready to beat the piss out of it again.
There are currently 1 users browsing this thread. (0 members and 1 guests)