Jeep parts garage sale CJ

[jackb1]

Re-Updated 8-24:

I've got a lot of CJ parts that I'd like to thin out. Most are small parts a pack-rat would keep when parting out a CJ, but there are some larger parts too. If you're looking for something, ask, I might have it. Pricing is all on reasonable offer basis. I'm looking to thin out my parts collection, so I'll sell VERY reasonably.

For large parts, about all I have left is:

Dana 20 Tcase (2)

T150 3 speed transmission -needs simple rebuild but still works, just loud bearings.

Set of 5 steel wheels for a a 4 wheel drum brake CJ (I don't think they clear front disks). Bead blasted and painted lime green. 8" -Free

Mismatched CJ steel wheels -Free

Skid plate - CJ, but not sure of year (I think it was 1979)

CJ5 Frame 72-75 style (long front clip, parallel rails, C channel) similar to 76-83 -Free

360 2bbl cast manifold -$10

304 Flywheel

258 Flywheel

CJ hood, grill

Heater assembly no fan 72-77ish style

Cowl intakes (2)

Clutches (3)

Driveshafts - all CJ and no CJ7 rears.

Seat brackets CJ

CJ 2 bolt disk caliper brackets

CJ steering column 76-86 style. Non-tilt, no key and a little rough.


Small parts:

Various brackets, used alternators, starters, bellhousings to guages. I have at least one of most small parts on a CJ.

[scrambled]

power steering ??????

[UPJ Wheeler]

lookn for a drive shaft that would work for a 35" running length, Im thinking around 34" collapsed or so

[jackb1]

Scrambled
I've got a few manual boxes, but I'll have to look for a PS box. If I've got one, I'll get back to you. I know I have a scout box if you want to stretch your front some.

UPJ
I'll try to dig into the shafts today and let you know.

[scrambled]

[quote=jackb1]Scrambled
I've got a few manual boxes, but I'll have to look for a PS box. If I've got one, I'll get back to you. I know I have a scout box if you want to stretch your front some.


Thanks jackb, I thought I asked you about this when I picked up the springs but I wasnt sure. My brain is as max capacity so new data overwrites old data. Thanks for checking......

[Wrecker]

Thanks jackb, I thought I asked you about this when I picked up the springs but I wasnt sure. My brain is as max capacity so new data overwrites old data. Thanks for checking......

Capacity is 5 thoughts.

[jackb1]

lookn for a drive shaft that would work for a 35" running length, Im thinking around 34" collapsed or so

I've got about 10 from CJs, but the longest was 30" fully extended. Is this for a CJ7 rear?

[UPJ Wheeler]

I already found one, thanks though

[jackb1]

Ok, 6 month update... anybody want some junk?

[gonecheenin]

Ok, 6 month update... anybody want some junk?

We could go wheelin' finally & add to the junk

[2002wranglerX]

cj dash and gauges?

[2002wranglerX]

cj support rods for under the hood from firewall to grill. for cj7 not 5?

[jackb1]

We could go wheelin' finally & add to the junk

I just cleaned out from around the samurai yesterday and started on it again. I'll make a stocker run soon with the CJ.

cj dash and gauges?

Yes... but the guages are all out in boxes. No tach/clock. I have at least one, maybe 2.

cj support rods for under the hood from firewall to grill. for cj7 not 5?

Wouldn't they be the same, but no. Just get some threaded rod unless you are restoring factory?

[gonecheenin]

I just cleaned out from around the samurai yesterday and started on it again. I'll make a stocker run soon with the CJ.

Cool


Come on up my place sometime soon & we'll get some laid back trailtime under them tires

[EddyB]

Do you have hubcaps for a '72 Pinto?

[wozz]

I'm looking for a front driveshaft for a auto cj with a 258. I think that its also a 35 inch running length.

thanks

[jackb1]

Do you have hubcaps for a '72 Pinto?

I only have hubcaps for a '71 Pinto... however these are very rare and worth $$$ so I keep them on display in my living room and am not prepared to sell.

I'm looking for a front driveshaft for a auto cj with a 258. I think that its also a 35 inch running length.

thanks

I thought my longest was 30" extented, but I found one that is 30 1/2" collapsed... I'm guessing still a little short for you.

[jackb1]

cj dash and gauges?

I do have 2, green and brown from a 77 and 79 (I think) respectively.

[jackb1]

How much for a used {working or not} alternator and C channel frame pieces,{to box sections of my frame}?

You can have an alternator because I didn't keep track of what I know works vs. what might work. The same for the CJ frame.... but you have to take the whole thing.

[seejay-5]

How much for a steering column, and for what year is your heater?

[jackb1]

How much for a steering column, and for what year is your heater?

I think I still have a lower steering shaft laying around but no columns. I'll double check, but pretty sure it's a no. I have a 72-77 and 78-80 (I think that is the split). What year do you want?

[seejay-5]

I need a 1975. Is it complete? I bought an aftermarket one and it gets hot, but the fan in it doesnt blow very hard. I was wondering if the factory one was any better. Thanks,Roy

[jackb1]

I need a 1975. Is it complete? I bought an aftermarket one and it gets hot, but the fan in it doesnt blow very hard. I was wondering if the factory one was any better. Thanks,Roy

Yeah.

Edit: Sorry, but I was wrong. Once I dug back to it, I already took the fan out.

[jackb1]

How much for a steering column, and for what year is your heater?

While digging for the heater I found a column I didn't know I had. I don't have a key for it, standard transmission.

[JPatten]

Do you still have that CJ grill?