anyone know of anyone that can install gears in a D30 and a ford 8.8 fairly cheap? might try it myself, but i will have to do it without the gauges and stuff the pro's use. any pointers for me doing it myself or should i just hire a pro to do it?
anyone know of anyone that can install gears in a D30 and a ford 8.8 fairly cheap? might try it myself, but i will have to do it without the gauges and stuff the pro's use. any pointers for me doing it myself or should i just hire a pro to do it?
98 grand cherokee 5.9L, 2"BB, BFG A/T ko's
91 S-10, 35" baja claw radials, ZZ4 350 crate motor
93 YJ, 33" MTR, 4.56, 8.8 (was locked for 4 miles...) 2.5L (not forever...)
[url]www.bigrubbers4x4.org[/url]
pretty complete article here Sam, it's what I followed when I put the 3.73's in my 30. All you have to get is the torque specs from elsewhere on the web.
LINK: http://www.pirate4x4.com/tech/billavista/Gear_Setup/
I don't suffer from insanity........................I enjoy every minute of it!!!!!!!!!
[URL="http://www.bigrubbers4x4.org"]www.bbnt4x4.org[/URL]
I have acess to a lash gauge and have set up many axles say 50 bucks a axle and your on your way
94 Cherokee Up 6" and on 33
98 grand cherokee 5.9L, 2"BB, BFG A/T ko's
91 S-10, 35" baja claw radials, ZZ4 350 crate motor
93 YJ, 33" MTR, 4.56, 8.8 (was locked for 4 miles...) 2.5L (not forever...)
[url]www.bigrubbers4x4.org[/url]
do you have a garage with acess to air tools and heat?
94 Cherokee Up 6" and on 33
98 grand cherokee 5.9L, 2"BB, BFG A/T ko's
91 S-10, 35" baja claw radials, ZZ4 350 crate motor
93 YJ, 33" MTR, 4.56, 8.8 (was locked for 4 miles...) 2.5L (not forever...)
[url]www.bigrubbers4x4.org[/url]
The PBB article is good. That was going to be my suggestion also. I would also say to make sure you have every necessary tool possible, end then some for a litle creature comfort. An axle stand is probably one of the greatest things I've ever made! Seriously...think about it. Who wants to be hunched over a stinky rear end for hours?
I'm not completely worthless, I can always serve as a bad example.
[COLOR=red]Every time I walk into a singles bar I think of my mom's wise words, "Don't pick that up, you don't know where it's been." [/COLOR]
my address is:
1269 Centennial Dr
Windber Pa 15963
if he dont mind, i dont care if ya bring yours by at the same time to have a wrenchfest............lol
98 grand cherokee 5.9L, 2"BB, BFG A/T ko's
91 S-10, 35" baja claw radials, ZZ4 350 crate motor
93 YJ, 33" MTR, 4.56, 8.8 (was locked for 4 miles...) 2.5L (not forever...)
[url]www.bigrubbers4x4.org[/url]
you guys wanna set something up for saturday?
94 Cherokee Up 6" and on 33
saturday may not work for me, i will be working on my new house or hunting. sometime next weekend would be better for me. how about you dodgemudder, when is a good time for you?
98 grand cherokee 5.9L, 2"BB, BFG A/T ko's
91 S-10, 35" baja claw radials, ZZ4 350 crate motor
93 YJ, 33" MTR, 4.56, 8.8 (was locked for 4 miles...) 2.5L (not forever...)
[url]www.bigrubbers4x4.org[/url]
the next weekend would be good for me as well let me know
94 Cherokee Up 6" and on 33
I'm not completely worthless, I can always serve as a bad example.
[COLOR=red]Every time I walk into a singles bar I think of my mom's wise words, "Don't pick that up, you don't know where it's been." [/COLOR]
i already have my 4.56 gears, master install kits, new front carrier, and rear locker and titanium pin.
how long do you think it will take you to get your gears?
98 grand cherokee 5.9L, 2"BB, BFG A/T ko's
91 S-10, 35" baja claw radials, ZZ4 350 crate motor
93 YJ, 33" MTR, 4.56, 8.8 (was locked for 4 miles...) 2.5L (not forever...)
[url]www.bigrubbers4x4.org[/url]
lol its not that hard, check the backlash before you take the gears out by hand then when you put them back in, make sure its the same and put some paint on the ring gear and spin it around to check the gear mesh and your good lol did it to my truck several times
02 ZR2 Sonoma- 4.3, 5spd, DD/Bike Hauler
07 TRX400EX- XRC-ish woods krewser
04 KX220 Hybrid Woods Weapon
97 KDX220 Plated Street/Woods beater
Need some Powder Coating done? Let me know!
o haha yea nevermind... i've just had the diff apart, my bad guys. it definitly wouldnt work like that with new gears
02 ZR2 Sonoma- 4.3, 5spd, DD/Bike Hauler
07 TRX400EX- XRC-ish woods krewser
04 KX220 Hybrid Woods Weapon
97 KDX220 Plated Street/Woods beater
Need some Powder Coating done? Let me know!
I'm not completely worthless, I can always serve as a bad example.
[COLOR=red]Every time I walk into a singles bar I think of my mom's wise words, "Don't pick that up, you don't know where it's been." [/COLOR]
hey, it dont matter to me man. whatever you want to do.
slowhite, when do you want to come out?
98 grand cherokee 5.9L, 2"BB, BFG A/T ko's
91 S-10, 35" baja claw radials, ZZ4 350 crate motor
93 YJ, 33" MTR, 4.56, 8.8 (was locked for 4 miles...) 2.5L (not forever...)
[url]www.bigrubbers4x4.org[/url]
There are currently 1 users browsing this thread. (0 members and 1 guests)